ULS-XSpot-G3

• 1: ULS-XSpot-G3 Datasheet
• 2: ULS-XSpot-G3 Interface Control Document
• 3: ULS-XSpot-G3 Operation Manual

1 - ULS-XSpot-G3 Datasheet

ULSDC-PBDS190426 · version 0.1.6 · issued August 9, 2026
The numbered PDF is the controlled copy: download it from the portal.

Introduction

Purpose

The purpose of this datasheet is to provide a concise technical overview of the ULS-XSpot-G3 system, the third generation of the ULS-XSpot tethered drone precision positioning system. The document is intended to help customers, evaluators, and integrators understand the product role, key characteristics, and integration fit. Detailed interface definitions remain in the Interface Control Document.

Scope

This document is intended for system engineers, integrators, and developers preparing ULS-XSpot-G3 integration with tethered drone platforms and autopilot systems.

Intended Audience

This datasheet is intended for customers, sales engineers, system integrators, and technical evaluators.

Product Overview

ULS-XSpot-G3 combines a tether-compatible ground transmitter with 2 identical RXM onboard receivers and shares the ULSDV-HLXS-G3-RXM receiver platform with ULS-Heli-G3. The architecture supports redundant onboard sensing and MRX-based yaw estimation for tethered flight and landing support.

ULS-XSpot-G3 and ULS-Heli-G3 are built on the same HL/XS G3 platform and have the same optical, electrical, and communication characteristics. The single difference is the transmitter case: the ULSDV-XS-G3-TX has a centre through hole (47mm x 47mm) that lets the tether cable pass through the unit, so the transmitter can be mounted directly at the tether exit point.

Key Features

1. Generation 3 Architecture: Shared ULSDV-HLXS-G3-RXM receiver hardware with ULS-Heli-G3 for improved logistics and spares management
2. Tether-compatible transmitter: Centre through hole for tether cable routing without obstructing the optical emission field
3. Dual RXM receivers: 2 identical, equal-priority RXM units for redundancy and triangular yaw estimation in MRX mode
4. Pulsed IR optical link: 940nm pulsed emission from transmitter to receivers
5. RS422 Interface: Receiver outputs RS422; UART-only autopilots require the ULS-XX-UART-RS422 onboard adapter
6. PC Configuration via USB-RS422: Ground-side USB-to-RS422 adapter (ULS-XX-USB-RS422) used to connect transmitter to PC

System Applications

• Tethered drone landing and station-keeping support
• Relative positioning for tethered aircraft operations
• Integration with supported autopilot and mission systems

System Base Components

Transmitter (Ground Unit)

The ULS-XSpot-G3 transmitter (ULSDV-XS-G3-TX) is the ground-side unit that emits the optical IR positioning field. It uses the same optical, electrical, and communication design as the ULS-Heli-G3 transmitter (ULSDV-HL-G3-TX); the only difference is a through hole in the centre of the case that allows the tether cable to pass through the unit.

• Device code: ULSDV-XS-G3-TX
• Primary function: Optical IR field emission for precision positioning
• Optical emission parameters: 940nm, pulsed
• Tether-compatible design: centre through hole (47 x 47 mm) for tether cable passage

Figure: ULSDV-XS-G3-TX Transmitter

Receiver (Onboard Unit)

The ULS-XSpot-G3 uses the shared ULSDV-HLXS-G3-RXM receiver unit, identical to the one used in ULS-Heli-G3.

• Device code: ULSDV-HLXS-G3-RXM
• Primary function: Optical IR field sensor for precision positioning
• Optical central wavelength: 940nm

System architecture uses 2 identical RXM receiver units operating with the same priority.

Both RXM units are used for redundancy and for yaw orientation estimation using a triangular method in MRX mode.

Figure: ULSDV-HLXS-G3-RXM Receiver

RS422–UART Onboard Adapter

When the autopilot has only a UART interface, the ULSDV-HLXS-G3 RS422-to-UART adapter (ULS-XX-UART-RS422) is used onboard to connect the ULSDV-HLXS-G3-RXM receiver to the autopilot.

Figure: ULS-XX-UART-RS422 Onboard Adapter

USB–RS422 Ground Adapter

The ULS-XX-USB-RS422 adapter is used on the ground to connect the ULSDV-XS-G3-TX transmitter to a PC for configuration and control.

Figure: ULS-XX-USB-RS422 Ground Adapter

System Wiring Schematics

Figure: HL/XS G3 Ground-Side Wiring Schematic

Figure: HL/XS G3 Onboard Wiring Schematic

Part Numbering

Table: Part Numbering

System Specifications

Table: Common Specification

Table: ULSDV-HLXS-G3-RXM Receiver Specifications Both RXM units (Set A and Set B) are the same hardware and share the specification above.

Table: ULSDV-XS-G3-TX Transmitter (Ground) Specifications

Interface Summary

The ULS-XSpot-G3 system uses optical, RS422, CAN, USB, and adapter-assisted UART connectivity depending on subsystem role and host platform capability.

• Transmitter to receiver: optical IR link, 940nm pulsed
• Transmitter to control PC: USB to RS422 adapter path
• Receiver to host system: native RS422, CAN, USB, or adapter-assisted UART

For connector, pinout, signal, and protocol definitions, refer to ULSDC-PBICD190426-ULS-XSpot-G3-ICD.

Mechanical Dimensions

Table: Mechanical Dimensions

Figure: ULSDV-XS-G3-TX Projection Views (Color)

Figure: ULSDV-XS-G3-TX Transmitter Dimensions

Figure: ULSDV-HLXS-G3-RXM Projection Views (Color)

Figure: ULSDV-HLXS-G3-RXM Receiver Dimensions

Packaging Information

Table: Packaging Information

Environmental Conditions

Equipment is designed to meet stringent military and maritime operational requirements, providing reliable performance in the most demanding environmental conditions including shipboard operations, offshore platforms, and tactical deployments.

Operating Temperature Range

• Extended operating range: -40°C to +85°C
• Meets MIL-STD-810 requirements for temperature extremes
• Arctic to desert operations capability
• No performance degradation across full temperature range
• Qualified for rapid temperature transitions and thermal shock
• Cold-soak start capability from -40°C

Humidity and Salt Fog Resistance

• Relative humidity: Up to 95% (condensing)
• Salt fog resistant per MIL-STD-810 Method 509
• Maritime environment qualified for shipboard operations
• Corrosion-resistant materials and protective coatings
• Protected against salt spray and marine atmosphere
• Suitable for offshore platform installations

Ingress Protection

• IP67 rated (Dust tight and water immersion resistant)
  • 6 - Complete protection against dust, sand, and particulate ingress
  • 7 - Protected against temporary immersion in water (up to 1 meter depth for 30 minutes)
• Exceeds requirements for shipboard and maritime operations
• Protected against:
  • Heavy rain and sea spray
  • Temporary submersion (deck washing, wave impact)
  • Sand and dust storms
  • Contaminated environments

Shock and Vibration

• Vibration: MIL-STD-810 Method 514
  • Helicopter vibration profile qualified
  • Shipboard vibration and shock resistant
  • Continuous operation during vibration
• Mechanical Shock: MIL-STD-810 Method 516
  • Drop and impact qualified
  • Transportation and handling shock resistant
  • Crash survival design considerations

Electromagnetic Compatibility

• EMI/EMC: MIL-STD-461 compliant
  • Electromagnetic interference immunity
  • Low electromagnetic emissions
  • RF coexistence with military avionics
  • Lightning protection per MIL-STD-464
• ESD Protection: IEC 61000-4-2
  • Contact discharge: ±8kV
  • Air discharge: ±15kV

Storage Conditions

• Storage temperature: -55°C to +85°C
• Relative humidity: Up to 95% (condensing)
• Long-term storage in uncontrolled environments
• Sealed for preservation and long-term depot storage

Altitude and Pressure

• Operating altitude: -500m to +4500m above sea level
• Storage altitude: -500m to +12000m
• Pressure differential resistant
• Suitable for high-altitude helicopter operations

Maintenance and Serviceability

• Designed for field maintenance and repair
• Minimal preventive maintenance required
• Accessible components for service and inspection
• Environmental seals serviceable in the field
• Long service intervals suitable for deployed operations

Note: All environmental specifications are subject to final qualification testing. Contact UAVLAS for the most current test data and certification documentation. Custom environmental testing and certification to specific standards available upon request.

Optical Radiation Safety (IR Emission)

The transmitter (ground unit) emits pulsed infrared optical radiation with a centre wavelength of 940nm. The receivers are optical sensors only and do not emit optical radiation.

Why This Warning Is Given

Radiation at 940nm is outside the visible range. The protective mechanisms that limit exposure to bright visible sources — the blink reflex, pupil constriction, and the instinct to look away — are not triggered by an invisible source. Exposure time is therefore limited only by operator behaviour, which is why the precautions below are given as operating instructions and not left to the operator’s judgement.

The transmitter is a positioning beacon. It is not an illumination product and is not intended to be viewed at any time.

Operating Precautions

• Do not look directly into the transmitter emitter apertures from a distance of less than 1 metre while the unit is powered.
• Treat the transmitter as emitting whenever supply voltage is applied, including when no receiver is present and no positioning data is being transferred.
• Switch emission off before working directly in front of the transmitter. Use the Illumination parameter in ULS-Tools to disable emission, or disconnect supply power.
• Do not view the powered transmitter through binoculars, telescopes, camera lenses, magnifiers, or any other light-collecting instrument. Such optics concentrate the emission and can raise the exposure at the eye by orders of magnitude compared with unaided viewing.
• Do not add, remove, or modify optical elements of the transmitter. Added optics change the emission characteristics and invalidate any photobiological classification of the unit.
• Position the transmitter so that the emission field is directed away from work positions and walkways where personnel stay for extended periods.
• Servicing personnel working inside the emission field at close range should disable emission first rather than rely on viewing distance.

Classification and Applicable Standards

Table: Optical Radiation Safety Data

For a 940nm source the applicable exposure limits are the retinal thermal hazard (380nm to 1400nm), the retinal thermal hazard for a weak visual stimulus (780nm to 1400nm, which applies specifically to sources that give no visual cue), and the infrared hazard to the cornea and lens (780nm to 3000nm). The corneal and lens limits are intended for chronic exposures longer than 1000s at a daily averaged irradiance of 100 W/m² or more.

Organisations operating this equipment within the European Union are additionally subject to Directive 2006/25/EC on the exposure of workers to artificial optical radiation, which requires the employer to assess worker exposure against the exposure limit values given in Annex I of that directive. UAVLAS provides the emission data needed for that assessment on request.

Compliance and Standards

• Document classification and release control as defined in metadata
• Product-specific compliance statements to be finalized for release

Ordering Information

Use the part numbering section to identify system variants, subassemblies, and related accessories.

Change Control

All changes to this document must be reviewed and approved by the relevant technical leads and stakeholders

References

• ULSDC-PBICD190426-ULS-XSpot-G3-ICD
• ULSDC-PBOM190426-ULS-XSpot-G3-Operation-Manual

2 - ULS-XSpot-G3 Interface Control Document

ULSDC-PBICD190426 · version 0.1.6 · issued August 9, 2026
The numbered PDF is the controlled copy: download it from the portal.

Introduction

Purpose

This document defines the interfaces between ULS-XSpot-G3 components, including one tether-compatible transmitter (ULSDV-XS-G3-TX) and 2 identical, equal-priority RXM receivers (ULSDV-HLXS-G3-RXM). The dual RXM architecture is used for redundancy and for yaw orientation estimation using a triangular method in MRX mode.

ULS-XSpot-G3 shares the HL/XS G3 platform with ULS-Heli-G3. Optical, electrical, and communication interfaces are identical to ULS-Heli-G3; the only difference is the transmitter case, which has a centre through hole for tether cable passage.

Scope

This document is intended for system engineers, integrators, and developers working with ULS-XSpot-G3 systems in tethered drone applications.

Assumptions and Exclusions

• This document defines interfaces only; product selection and overview information belong in the datasheet.
• Installation, calibration, and operating procedures belong in the operation manual.

System Components

Transmitter (Ground Unit)

The ULS-XSpot-G3 transmitter (ULSDV-XS-G3-TX) is the ground-side unit that emits the optical IR positioning field. It uses the same optical, electrical, and communication design as the ULS-Heli-G3 transmitter (ULSDV-HL-G3-TX); the only difference is a through hole in the centre of the case that allows the tether cable to pass through the unit.

• Device code: ULSDV-XS-G3-TX
• Primary function: Optical IR field emission for precision positioning
• Optical emission parameters: 940nm, pulsed
• Tether-compatible design: centre through hole (47 x 47 mm) for tether cable passage

Figure: ULSDV-XS-G3-TX Transmitter

Receiver (Onboard Unit)

The ULS-XSpot-G3 uses the shared ULSDV-HLXS-G3-RXM receiver unit, identical to the one used in ULS-Heli-G3.

• Device code: ULSDV-HLXS-G3-RXM
• Primary function: Optical IR field sensor for precision positioning
• Optical central wavelength: 940nm

System architecture uses 2 identical RXM receiver units operating with the same priority.

Both RXM units are used for redundancy and for yaw orientation estimation using a triangular method in MRX mode.

Figure: ULSDV-HLXS-G3-RXM Receiver

RS422–UART Onboard Adapter

When the autopilot has only a UART interface, the ULSDV-HLXS-G3 RS422-to-UART adapter (ULS-XX-UART-RS422) is used onboard to connect the ULSDV-HLXS-G3-RXM receiver to the autopilot.

Figure: ULS-XX-UART-RS422 Onboard Adapter

USB–RS422 Ground Adapter

The ULS-XX-USB-RS422 adapter is used on the ground to connect the ULSDV-XS-G3-TX transmitter to a PC for configuration and control.

Figure: ULS-XX-USB-RS422 Ground Adapter

Interface Overview

Figure: ULS-XSpot-G3 System Interfaces Overview

Interface Summary

• Transmitter to control PC
• Transmitter to receiver optical link
• Receiver to autopilot, PC, and network interfaces
• Power distribution and interface-related electrical constraints

Physical Interfaces

Figure: ULS-XSpot-G3 Physical Interfaces Overview

Transmitter to Control PC Interface

The transmitter (ULSDV-XS-G3-TX) connects to a PC via the ULS-XX-USB-RS422 ground adapter for configuration and control.

Figure: ULS-XX-USB-RS422 Adapter Pinout

*Table: ULS-XX-USB-RS422 Pinout *

Data Types

• Status information
• Control signals
• Transmitter configuration
• External IMU/COMPASS data

Connection Types

• CAN Bus – For network communication
• USB – Via ULS-XX-USB-RS422 adapter (PC side)
• RS422 – Native transmitter interface; for serial communication with external sensors

Transmitter Pinout

ULSDV-XS-G3-TX Transmitter pinout information.

Figure: Transmitter connector

Table: Transmitter Connector Pinout (ULSDV-XS-G3-TX)

The transmitter connects to a PC via the ULS-XX-USB-RS422 ground adapter (USB side to PC, RS422 side to transmitter connector).

Transmitter to Receiver Interface

The transmitter and receiver use an optical interface to exchange data. Transmission uses pulsed IR emission at 940 nanometers. Data transmission is only in the direction from the transmitter to the receiver.

Data Types

• Position encoded
• Status encoded data (transmitter orientation and instructions)

Connection Type

• Optical IR 940nm (pulsed) – Infrared optical link

Receiver Interfaces (RXM Set A and RXM Set B)

Both RXM receivers (ULSDV-HLXS-G3-RXM) are identical and have the same priority in system operation.

When the autopilot provides only a UART interface, connect the RXM receiver RS422 output through the ULS-XX-UART-RS422 onboard adapter.

Figure: ULS-XX-UART-RS422 Adapter Pinout

Table: ULSDV-XX-UART-RS422-R0 4 pin connector pinout

Table: ULSDV-XX-UART-RS422-R0 6 pin connector pinout

Data Types

• MAVLink messages
• ULS-Blitz frames
• ASCII protocol
• MRX-mode yaw estimation data (triangular method)

Connection Types

• RS422 – Native receiver interface
• UART – Via ULS-XX-UART-RS422 adapter (for UART-only autopilots)
• CAN – Network communication
• USB – Direct PC connection

Receiver Pinout

ULSDV-HLXS-G3-RXM Receiver pinout information.

Both receivers (Set A and Set B) are identical, equal-priority units. The pinout is the same for both.

Figure: Receiver connector

Table: ULSDV-HLXS-G3-RXM Connector Pinout When the autopilot provides only a UART interface, connect the receiver RS422 output to the autopilot via the ULS-XX-UART-RS422 onboard adapter.

For receiver setup unscrew protection part to get access to usb connector.

Figure: Receiver USB connector

Electrical Interfaces

Figure: Power Distribution and Connections

Transmitter Electrical Characteristics

Table: Transmitter Electrical Specifications Tethered System Power: Transmitter may be continuously powered from a ground station power supply via the tether cable.

Receiver Electrical Characteristics (Per RXM Set)

Table: Receiver Electrical Specifications

Communication Interfaces

Supported Communication Methods

• Optical IR 940nm pulsed link between transmitter and receiver
• RS422 for native wired subsystem interfaces
• UART via ULS-XX-UART-RS422 where required by the host autopilot
• CAN for network communication
• USB for direct PC access where supported

Data Definitions

Data Categories

• Position-encoded optical data
• Transmitter status and orientation data
• MAVLink messages
• ULS-Blitz frames
• ASCII protocol data
• MRX yaw estimation data

Message payload definitions are given in ULSDC-PBDS051125-ULS-DeCoNet Blitz Messages Specification.

Functional Interfaces

Figure: Data Flow and Functional Interfaces

Data Exchange

The ULS-XSpot-G3 system data exchange mechanism, applied to tethered drone operations:

Control PC Functions:

• Configure and view status of transmitter
• Set configuration of receivers
• Send control signals (On/off, compass override information)
• Monitor tethered operation parameters

External Equipment:

• External IMU/Compass equipment can be used to override internal IMU/compass information
• Tether management system integration for position reference

Receiver Functions:

• Accept data from transmitter over IR signal (position field information and ground unit IMU data)
• Accept NED and Attitude information from autopilot to convert coordinate system
• Multiple receivers (MRX mode) communicate to calculate vehicle orientation (YAW) using triangular method
• Send position offset data to autopilot
• Support for tethered flight modes and station-keeping

Mechanical Interfaces

Table: Mechanical Dimensions

Figure: ULSDV-XS-G3-TX Projection Views (Color)

Figure: ULSDV-XS-G3-TX Transmitter Dimensions

Figure: ULSDV-HLXS-G3-RXM Projection Views (Color)

Figure: ULSDV-HLXS-G3-RXM Receiver Dimensions

The transmitter centre through hole (47mm x 47mm) is reserved for tether cable passage. Do not route the tether cable across the optical emission apertures.

Environmental Conditions

Equipment is designed to meet stringent military and maritime operational requirements, providing reliable performance in the most demanding environmental conditions including shipboard operations, offshore platforms, and tactical deployments.

Operating Temperature Range

• Extended operating range: -40°C to +85°C
• Meets MIL-STD-810 requirements for temperature extremes
• Arctic to desert operations capability
• No performance degradation across full temperature range
• Qualified for rapid temperature transitions and thermal shock
• Cold-soak start capability from -40°C

Humidity and Salt Fog Resistance

• Relative humidity: Up to 95% (condensing)
• Salt fog resistant per MIL-STD-810 Method 509
• Maritime environment qualified for shipboard operations
• Corrosion-resistant materials and protective coatings
• Protected against salt spray and marine atmosphere
• Suitable for offshore platform installations

Ingress Protection

• IP67 rated (Dust tight and water immersion resistant)
  • 6 - Complete protection against dust, sand, and particulate ingress
  • 7 - Protected against temporary immersion in water (up to 1 meter depth for 30 minutes)
• Exceeds requirements for shipboard and maritime operations
• Protected against:
  • Heavy rain and sea spray
  • Temporary submersion (deck washing, wave impact)
  • Sand and dust storms
  • Contaminated environments

Shock and Vibration

• Vibration: MIL-STD-810 Method 514
  • Helicopter vibration profile qualified
  • Shipboard vibration and shock resistant
  • Continuous operation during vibration
• Mechanical Shock: MIL-STD-810 Method 516
  • Drop and impact qualified
  • Transportation and handling shock resistant
  • Crash survival design considerations

Electromagnetic Compatibility

• EMI/EMC: MIL-STD-461 compliant
  • Electromagnetic interference immunity
  • Low electromagnetic emissions
  • RF coexistence with military avionics
  • Lightning protection per MIL-STD-464
• ESD Protection: IEC 61000-4-2
  • Contact discharge: ±8kV
  • Air discharge: ±15kV

Storage Conditions

• Storage temperature: -55°C to +85°C
• Relative humidity: Up to 95% (condensing)
• Long-term storage in uncontrolled environments
• Sealed for preservation and long-term depot storage

Altitude and Pressure

• Operating altitude: -500m to +4500m above sea level
• Storage altitude: -500m to +12000m
• Pressure differential resistant
• Suitable for high-altitude helicopter operations

Maintenance and Serviceability

• Designed for field maintenance and repair
• Minimal preventive maintenance required
• Accessible components for service and inspection
• Environmental seals serviceable in the field
• Long service intervals suitable for deployed operations

Note: All environmental specifications are subject to final qualification testing. Contact UAVLAS for the most current test data and certification documentation. Custom environmental testing and certification to specific standards available upon request.

Optical Radiation Safety (IR Emission)

The transmitter (ground unit) emits pulsed infrared optical radiation with a centre wavelength of 940nm. The receivers are optical sensors only and do not emit optical radiation.

Why This Warning Is Given

Radiation at 940nm is outside the visible range. The protective mechanisms that limit exposure to bright visible sources — the blink reflex, pupil constriction, and the instinct to look away — are not triggered by an invisible source. Exposure time is therefore limited only by operator behaviour, which is why the precautions below are given as operating instructions and not left to the operator’s judgement.

The transmitter is a positioning beacon. It is not an illumination product and is not intended to be viewed at any time.

Operating Precautions

• Do not look directly into the transmitter emitter apertures from a distance of less than 1 metre while the unit is powered.
• Treat the transmitter as emitting whenever supply voltage is applied, including when no receiver is present and no positioning data is being transferred.
• Switch emission off before working directly in front of the transmitter. Use the Illumination parameter in ULS-Tools to disable emission, or disconnect supply power.
• Do not view the powered transmitter through binoculars, telescopes, camera lenses, magnifiers, or any other light-collecting instrument. Such optics concentrate the emission and can raise the exposure at the eye by orders of magnitude compared with unaided viewing.
• Do not add, remove, or modify optical elements of the transmitter. Added optics change the emission characteristics and invalidate any photobiological classification of the unit.
• Position the transmitter so that the emission field is directed away from work positions and walkways where personnel stay for extended periods.
• Servicing personnel working inside the emission field at close range should disable emission first rather than rely on viewing distance.

Classification and Applicable Standards

Table: Optical Radiation Safety Data

For a 940nm source the applicable exposure limits are the retinal thermal hazard (380nm to 1400nm), the retinal thermal hazard for a weak visual stimulus (780nm to 1400nm, which applies specifically to sources that give no visual cue), and the infrared hazard to the cornea and lens (780nm to 3000nm). The corneal and lens limits are intended for chronic exposures longer than 1000s at a daily averaged irradiance of 100 W/m² or more.

Organisations operating this equipment within the European Union are additionally subject to Directive 2006/25/EC on the exposure of workers to artificial optical radiation, which requires the employer to assess worker exposure against the exposure limit values given in Annex I of that directive. UAVLAS provides the emission data needed for that assessment on request.

Integration Wiring Diagrams

Figure: HL/XS G3 Ground-Side Wiring Schematic

Figure: HL/XS G3 Onboard Wiring Schematic

Part Numbering

Table: Part Numbering

Applicable Documents

• ULSDC-PBDS190426-ULS-XSpot-G3-Datasheet
• ULSDC-PBOM190426-ULS-XSpot-G3-Operation-Manual
• ULSDC-PBDS051125-ULS-DeCoNet Blitz Messages Specification

Change Control

All changes to this document must be reviewed and approved by the relevant technical leads and stakeholders

3 - ULS-XSpot-G3 Operation Manual

ULSDC-PBOM190426 · version 0.1.5 · issued August 9, 2026
The numbered PDF is the controlled copy: download it from the portal.

Introduction

Purpose

This manual provides installation, configuration, operation, verification, and troubleshooting guidance for the ULS-XSpot-G3 system.

Scope

This manual covers one tether-compatible transmitter and 2 identical, equal-priority RXM receivers used in the ULS-XSpot-G3 architecture.

Intended Audience

This manual is intended for operators, installers, technicians, and integrators responsible for commissioning and using the system.

Safety Information

• WARNING: The transmitter emits invisible infrared radiation when powered. Do not look into the emitter apertures at close range. See the Optical Radiation Safety section below.
• CAUTION: Route the tether cable through the transmitter centre through hole. Do not route the cable across the optical emission apertures.
• CAUTION: Do not connect or disconnect the transmitter interface under power.

Optical Radiation Safety (IR Emission)

The transmitter (ground unit) emits pulsed infrared optical radiation with a centre wavelength of 940nm. The receivers are optical sensors only and do not emit optical radiation.

Why This Warning Is Given

Radiation at 940nm is outside the visible range. The protective mechanisms that limit exposure to bright visible sources — the blink reflex, pupil constriction, and the instinct to look away — are not triggered by an invisible source. Exposure time is therefore limited only by operator behaviour, which is why the precautions below are given as operating instructions and not left to the operator’s judgement.

The transmitter is a positioning beacon. It is not an illumination product and is not intended to be viewed at any time.

Operating Precautions

• Do not look directly into the transmitter emitter apertures from a distance of less than 1 metre while the unit is powered.
• Treat the transmitter as emitting whenever supply voltage is applied, including when no receiver is present and no positioning data is being transferred.
• Switch emission off before working directly in front of the transmitter. Use the Illumination parameter in ULS-Tools to disable emission, or disconnect supply power.
• Do not view the powered transmitter through binoculars, telescopes, camera lenses, magnifiers, or any other light-collecting instrument. Such optics concentrate the emission and can raise the exposure at the eye by orders of magnitude compared with unaided viewing.
• Do not add, remove, or modify optical elements of the transmitter. Added optics change the emission characteristics and invalidate any photobiological classification of the unit.
• Position the transmitter so that the emission field is directed away from work positions and walkways where personnel stay for extended periods.
• Servicing personnel working inside the emission field at close range should disable emission first rather than rely on viewing distance.

Classification and Applicable Standards

Table: Optical Radiation Safety Data

For a 940nm source the applicable exposure limits are the retinal thermal hazard (380nm to 1400nm), the retinal thermal hazard for a weak visual stimulus (780nm to 1400nm, which applies specifically to sources that give no visual cue), and the infrared hazard to the cornea and lens (780nm to 3000nm). The corneal and lens limits are intended for chronic exposures longer than 1000s at a daily averaged irradiance of 100 W/m² or more.

Organisations operating this equipment within the European Union are additionally subject to Directive 2006/25/EC on the exposure of workers to artificial optical radiation, which requires the employer to assess worker exposure against the exposure limit values given in Annex I of that directive. UAVLAS provides the emission data needed for that assessment on request.

System Overview

ULS-XSpot-G3 is a tethered drone precision optical positioning system built around a tether-compatible ground transmitter (ULSDV-XS-G3-TX) and 2 equal-priority RXM onboard receivers (ULSDV-HLXS-G3-RXM). The system supports redundant onboard sensing and MRX-based yaw estimation for tethered flight and landing support.

ULS-XSpot-G3 uses the same HL/XS G3 platform as ULS-Heli-G3. Installation, configuration, and operating procedures are identical, except for the tether routing through the transmitter centre through hole (47mm x 47mm).

Package Contents

• 1x ULSDV-XS-G3-TX ground transmitter unit
• 2x ULSDV-HLXS-G3-RXM receiver units (Set A and Set B)
• 1x ULS-XX-USB-RS422 adapter (ground configuration)
• 2x ULS-XX-UART-RS422 onboard adapters (receiver-to-autopilot UART interface)
• Cables and mounting hardware
• Documentation package (may supply in online form)

System Requirements

• Transmitter power: +18V…+26V, 2.5A
• RXM receiver power (each): +12V…+26V, 1A
• Supported autopilots: Ardupilot and PX4 based systems (MAVLink V2), or any host supporting RS422/CAN/UART ULS protocols

Installation

Wiring Schematics

Figure: HL/XS G3 Ground-Side Wiring Schematic

Figure: HL/XS G3 Onboard Wiring Schematic

Transmitter Installation

The ULSDV-XS-G3-TX transmitter is a tether-compatible ground unit with a centre through hole for tether cable passage.

Figure: ULSDV-XS-G3-TX Transmitter

Figure: ULSDV-XS-G3-TX Dimensions

• Mounting instructions: device can be mounted from top side or from bottom side. Use corresponding M3 screws to mount device on place. 3D model and pad example can be provided by UAVLAS under request.
• Orientation requirements: The device must be positioned with the optical elements facing upward. Make sure that no foreign objects obstruct the optical elements within the transmitter’s entire field of view.
• Tether routing: route the tether cable through the centre through hole (47mm x 47mm) before mounting. The tether must not cross the optical emission apertures.

Receiver Installation

Both receivers are identical and operate with equal priority.

Figure: ULSDV-HLXS-G3-RXM Receiver

Figure: ULSDV-HLXS-G3-RXM Dimensions

• Receivers location and orientation: The device must be positioned with the optical elements facing downward. Ensure that the optical elements are not obstructed by foreign objects within the transmitter’s entire field of view.
• Install the receivers at least 0.5 meters apart; this will ensure reliable operation in MRX mode even if one of the receivers moves out of the system’s field of view. Typically, the first receiver (the one connected to the main autopilot) is located near the center of the landing point, and the second receiver is located at the tail. The maximum installation distance is 3 meters.

Configuration

Connecting Transmitter to PC

Use the ULS-XX-USB-RS422 adapter to connect the transmitter RS422 interface to a PC USB port for configuration and control via ULS-Tools software.

Figure: ULS-XX-USB-RS422 Ground Adapter

Figure: ULS-XX-USB-RS422 Adapter Pinout

Connecting Receiver to UART Autopilot

When the autopilot provides only a UART interface, use the ULS-XX-UART-RS422 onboard adapter between the receiver RS422 output and the autopilot UART port.

Figure: ULS-XX-UART-RS422 Onboard Adapter

Figure: ULS-XX-UART-RS422 Onboard Adapter Pinout

Receiver Pinout

ULSDV-HLXS-G3-RXM Receiver pinout information.

Both receivers (Set A and Set B) are identical, equal-priority units. The pinout is the same for both.

Figure: Receiver connector

Table: ULSDV-HLXS-G3-RXM Connector Pinout When the autopilot provides only a UART interface, connect the receiver RS422 output to the autopilot via the ULS-XX-UART-RS422 onboard adapter.

For receiver setup unscrew protection part to get access to usb connector.

Figure: Receiver USB connector

Transmitter Pinout

ULSDV-XS-G3-TX Transmitter pinout information.

Figure: Transmitter connector

Table: Transmitter Connector Pinout (ULSDV-XS-G3-TX)

The transmitter connects to a PC via the ULS-XX-USB-RS422 ground adapter (USB side to PC, RS422 side to transmitter connector).

Device Configuration and Integration in ULS-Tools

Use the adapters listed in this manual to connect each device to a PC and complete configuration in ULS-Tools before field operation.

ULS-Tools Device Dashboard

Figure: ULS-Tools Device Dashboard

Configure Transmitter

1. Connect the transmitter through the ULS-XX-USB-RS422 adapter.
2. Open transmitter settings and verify communication parameters.
3. Set required operating parameters and click Apply Config.

Figure: ULS-Tools Transmitter Configuration

Table: Transmitter Configuration Parameters

Configure Receiver (RXM)

1. Connect each receiver and configure one at a time.
2. Set UART protocol/baud rate to match autopilot serial configuration.
3. For dual-receiver installation, verify MRX-related parameters and offsets.
4. Click Apply Config after each update.

Figure: ULS-Tools Receiver Configuration

Table: Receiver Configuration Parameters

Compass Calibration (Ground Unit)

After installation, check compass behavior and perform calibration if required.

1. Press Reset calibrations.
2. Rotate the ground unit through multiple orientations to fill calibration charts.
3. Press Apply calibration and Apply Config.

Figure: ULS-Tools Compass Calibration

Integration Verification in ULS-Tools

• Confirm live device telemetry is visible in charts.
• Verify stable IMU and system parameter traces before flight tests.
• Confirm receiver link and valid position updates prior to autopilot integration tests.

Figure: ULS-Tools System Parameters Chart

Figure: ULS-Tools Receiver Charts

Integration Instructions for Ardupilot Based Systems

Preparing for Integration

• Download the latest version of ULS-Tools (Beta). It is recommended to connect all devices to a PC and update firmware for all UAVLAS devices before proceeding.
• Update the autopilot to the latest Arducopter version.
• Configure the transmitter in ULS-Tools
• Configure both receivers in ULS-Tools

The system communicates with Ardupilot using the MavlinkV2 protocol (supports MAV_FRAME_BODY_FRD).

Autopilot Configuration

Setup PLND Section

Table: Ardupilot PLND Section Parameters All other PLND parameters should remain at defaults, or be set according to your vehicle requirements.

Figure: PLND Configuration Example

Set Up Serial Communication in SERIALx Section

Table: Ardupilot SERIALx Section Parameters Set up serial stream rates in the SRx section. The sensor requires the following data from the autopilot:

Table: Ardupilot SRx Stream Rate Parameters

Check Setup

When configuration and wiring are correct, GPS is available, and the receiver is in the field of view of the transmitter, you will see the LANDING_TARGET MAVLink message in the MAVLink Inspector (Mission Planner example shown):

Figure: LANDING_TARGET Message in MAVLink Inspector

Setup Precision Loiter Mode

Attach any unused switch to the PrecLoiter option to enable precision loiter mode:

Figure: PrecLoiter Switch Configuration

Activate the switch and confirm messages “PrecLoiter: LOW” and “PrecLoiter: HIGH” appear. After a test flight above the target, check telemetry for PL offset data.

Figure: Telemetry Data Showing PL Offsets

PID Tuning

In case of oscillations or instability during landing, check the PID parameters in Ardupilot Extended Tuning.

It is recommended to tune Position XY, Velocity XY, and Loiter Speed for the best performance:

Figure: Ardupilot Extended Tuning Parameters

For additional information, see the Ardupilot documentation at https://ardupilot.org/ardupilot/

Integration Instructions for PX4 Based Systems

Preparing for Integration

• Download the latest version of ULS-Tools (Beta). It is recommended to connect all devices to a PC and update firmware for all UAVLAS devices before proceeding.
• Update the autopilot to the latest PX4 version.
• Configure the transmitter in ULS-Tools.
• Configure both receivers in ULS-Tools.

The system communicates with PX4 using the MavlinkV2 protocol (supports MAV_FRAME_LOCAL_NED).

Configure PX4 Autopilot

Values are provided as an example (Pixhawk4-mini AP):

Table: PX4 Autopilot Configuration Parameters

Running and Testing

After configuration and wiring, power up the drone and transmitter. In QGroundControl, go to Analyze Tools → MAVLink Inspector and check for the LANDING_TARGET MAVLink message.

If the vehicle is providing a LOCAL_POSITION_NED message to the UAVLAS system and is hovering over the beacon, the field position_valid = 1 will appear in LANDING_TARGET.

To perform precision landing, create a flight plan and enable the Precision Landing option on the landing waypoint.

Figure: LANDING_TARGET Message in QGroundControl

For additional information, see the PX4 documentation at https://docs.px4.io/main/en/

Operating Instructions

• Power sequence: Power device after all connectors are plugged in before powering.
• Link check procedure: Link can be checked from the configuration system during system installation, as well as during operation using a third-party device via the appropriate protocols.
• Landing and approach operation notes: The vehicle’s control system independently decides on the appropriate action based on the status of the landing system. The UAVLAS system acts as a sensor—the procedure for handling abnormal situations during operation remains the responsibility of the unmanned vehicle’s control system.
• Equal-priority RXM behavior in MRX mode: Both receivers have the same priority, and either one can be used to receive system status data.
• Tethered operation: verify that the tether cable stays inside the transmitter centre through hole over the full range of tether movement.

Service and Support

The device requires no maintenance throughout its service life.

Appendices

Technical Reference

Table: Common Specification

Table: ULSDV-HLXS-G3-RXM Receiver Specifications Both RXM units (Set A and Set B) are the same hardware and share the specification above.

Table: ULSDV-XS-G3-TX Transmitter (Ground) Specifications

Change Control

All changes to this document must be reviewed and approved by the relevant technical leads and stakeholders

References

• ULSDC-PBDS190426-ULS-XSpot-G3-Datasheet
• ULSDC-PBICD190426-ULS-XSpot-G3-ICD